Insulation Removal & Replacement in Georgetown - Same-Day Service, Done Right the First Time

Trusted Insulation Removal & Replacement for Georgetown Homeowners

Insulation removal and replacement in Georgetown typically costs $2,800-$7,500 for a full attic, depending on contamination level, square footage, and whether hazardous materials like vermiculite are present. Most jobs take one to three days, and we can start with a written price within 24 hours of your call. Call (254) 970-2136 - a live person answers, even at midnight.

Call (254) 970-2136

We’ve been independently owned and operated under The Haven Standard since 2016, and we’ve sealed and insulated more than 9,000 homes across Central Texas. In Georgetown specifically, we regularly work in neighborhoods like Serenada, Sun City, and the historic district near Southwestern University, where homes built between the 1970s and early 2000s often contain insulation that’s compressed, water-stained, or contaminated by rodents. The Hill Country humidity doesn’t help - moisture gets trapped, mold follows, and R-values drop to where your HVAC runs constantly in August. We don’t just pull out the old material and blow in new. We air-seal first - top plates, can lights, penetrations - then insulate, and we publish before-and-after blower-door numbers so you see exactly what changed.

Every job starts with a written price and a written scope. No exceptions. That’s Haven Standard Clause 1.

What Our Insulation Removal & Replacement Service Includes

Attic Insulation Removal

Attic insulation removal is the complete extraction of existing fiberglass batts, blown-in cellulose, or loose-fill mineral wool from your attic floor and joist cavities. You need this when insulation has settled below its original R-value, been disturbed by wiring or plumbing work, or simply reached the end of its functional life - typically 15-20 years for fiberglass, less if there’s been moisture intrusion. In Georgetown, we see a lot of attics where original blown-in fiberglass has compressed to half its loft, especially in homes near the San Gabriel River basin where humidity runs higher. Our crew uses commercial HEPA-filtered vacuums and negative-air machines to contain dust, and we document the empty cavity with photos before any new material goes in. You’ll receive that photo record as part of your job file.

Contaminated Insulation Removal

Contaminated insulation removal addresses material compromised by rodent droppings, urine, mold spores, or sewage backup - situations where the insulation itself becomes a health hazard, not just an efficiency problem. You need this if you’ve had rats, raccoons, or squirrels nesting in your attic, or if a roof leak went undetected long enough for mold to colonize the fiberglass or cellulose. In neighborhoods like Berry Creek and Georgetown Village, we’ve pulled out insulation layers where the bottom third was essentially a compost bed of rodent waste. We treat these jobs as hazardous material operations: full PPE, sealed containment, EPA-registered disinfectant application, and disposal at licensed facilities. The attic isn’t ready for new insulation until it passes a visual clearance - and we photograph that too.

Vermiculite & Old Insulation Removal

Vermiculite and old insulation removal handles pre-1990s material, particularly the granular, pebble-like vermiculite insulation that was mined in Libby, Montana and may contain asbestos. You need this before any renovation, before selling a home built before 1990, or if you’re planning to add new insulation over material of unknown origin. Georgetown’s historic homes near the courthouse square and the older ranch-style houses off FM 1460 frequently test positive for vermiculite in our inspections. We do not disturb this material without third-party asbestos testing - it’s a hard rule. If asbestos is present, we coordinate with licensed abatement contractors and manage the project timeline so you’re not stuck with an open attic for weeks. The written scope includes exactly who does what, and when.

Insulation Replacement

Insulation replacement is the installation of new thermal material after removal, selected and installed to meet or exceed current IECC energy code for Williamson County. You need this after any removal, obviously, but also if you’re converting attic space to conditioned storage, adding a radiant barrier, or simply want to stop overworking your AC unit. We install Rockwool, CertainTeed, Icynene, and Demilec products depending on your budget, performance goals, and whether we’re treating the attic floor or the roof deck. In Georgetown’s climate - 95°F days, 30°F nights, and that persistent Hill Country wind - we typically recommend R-38 to R-49 for attic floors, installed only after blower-door-guided air sealing is complete. You get the before-and-after pressurization reading, the photo record, and a written warranty. That’s the full file.

Brands We Service for Insulation Removal & Replacement

We’ve worked extensively with Rockwool mineral wool batts and loose-fill, particularly in fire-separation applications between attached garages and living spaces where Georgetown’s municipal code requires a one-hour rated assembly. Rockwool’s density and moisture resistance make it our go-to for homes near the lake or in low-lying areas where humidity control is ongoing. We’ve also installed hundreds of CertainTeed fiberglass systems - their Optima and InsulSafe lines - in standard attic-floor retrofits where cost-performance ratio matters most. We know the compression characteristics, the proper netting for blown applications, and the common installation errors that void manufacturer warranties.

On the spray foam side, we regularly handle Icynene open-cell and Demilec closed-cell removals and replacements, usually in homes where the original foam was improperly mixed or applied too thin, leading to odor issues or thermal bridging. We don’t just cut out the bad foam - we identify why it failed, document the substrate condition, and specify the correct replacement product and thickness. Whether you have Rockwell, CertainTeed, Icynene, Demilec, or any other make, we can assess what’s there, remove what needs to go, and install what should replace it - with a written price before any work starts.

Before

After

Signs You Need Insulation Removal & Replacement Right Now

• Your energy bills spike every summer despite no rate increase. In Georgetown, a well-insulated 2,000-square-foot home should not see summer electric bills north of $280-$340 if the HVAC is properly sized. When we see $450+ bills, the attic is usually the first place we look. Compressed or missing insulation lets attic air - often 140°F in July - radiate straight through the ceiling.
• You smell something musty or animal-like when the HVAC runs. Your ductwork likely passes through the attic, and if that attic contains rodent-contaminated insulation, your system is pulling particulate through return leaks or flex connections. We’ve found active rodent highways in attics over Sun City and Teravista where the insulation was more nesting material than thermal barrier.
• Your insulation is flat, discolored, or wet to the touch. Healthy blown-in fiberglass should be fluffy and uniform in color. Water staining, usually yellow or brown, indicates roof leaks or condensation from unsealed ductwork. Flattened cellulose or fiberglass means it’s done its compressive life and is now conducting heat rather than resisting it.
• You’re renovating or adding recessed lighting. Every can light cut into your ceiling is a penetration through the thermal and air barrier. If your attic insulation is older, this is the moment to remove it properly, seal every penetration with fire-rated covers, and install new material to full depth around the new fixtures. Doing it twice costs more than doing it right once.
• Your home was built before 1990 and you’ve never inspected the attic. Vermiculite, rock wool with asbestos content, and early fiberglass formulations are common in Georgetown’s pre-boom housing stock. Disturbing these materials without testing creates liability for you and health risk for anyone in the home during or after the work.

Our Insulation Removal & Replacement Process - Step by Step

1. 1
   On-site assessment and blower-door test. We arrive at the scheduled time - you’ll get a text when the technician is en route - and begin with a visual attic inspection plus a blower-door test, a pressurization reading that shows, in one number, how much air your building envelope is losing. In Georgetown homes, we typically see 3,500-5,500 CFM50 before any work. We photograph the existing insulation condition, measure depths, and note any hazards.
2. 2
   Written price and scope delivered before work starts. Within 24 hours, you receive a flat price, a written scope of work, and a written warranty - Haven Standard Clause 1. No hourly rates, no “we’ll see how it goes” language. If you have a competing quote, bring it; we offer a Free Second Opinion and will read it with you line by line.
3. 3
   Containment, removal, and disposal. Our crew sets up HEPA-filtered negative air machines, seals attic hatches with temporary barriers, and removes material using commercial vacuums or bagged extraction depending on contamination level. All waste is transported to licensed disposal facilities; we retain manifests for your records.
4. 4
   Air sealing and substrate preparation. Before any new insulation touches your attic, we seal top plates, wire penetrations, plumbing stacks, can lights, and chimney chases using fire-rated foam, caulk, and rigid barriers. This is non-negotiable - we will not insulate over an unsealed attic floor. The blower-door test is repeated to quantify improvement.
5. 5
   Installation, final test, and documentation. New insulation is installed to specified depth and density, with photos taken at multiple stages. A final blower-door test captures your after number. You receive: the written invoice, the photo record, the before-and-after blower-door readings, and your warranty documentation. The 365-Day Done Right Promise applies from this date.

How Much Does Insulation Removal & Replacement Cost in Georgetown?

Insulation Removal & Replacement Near Georgetown - Our Service Area

We work throughout Georgetown and respond to surrounding communities including Round Rock, Brushy Creek, Leander, Hutto, Cedar Park, Jollyville, Wells Branch, Pflugerville, Taylor, Lago Vista, and Manor. Typical response time for a scheduled assessment in Georgetown proper is same-day or next-day; for outlying areas like Taylor or Lago Vista, we usually book within 48 hours. We also handle home energy audits and related envelope work across this entire service area, so if your project expands beyond insulation - say, into crawl space encapsulation or spray foam on the roof deck - we coordinate it under one written scope and one crew.

Frequently Asked Questions - Insulation Removal & Replacement in Georgetown

Schedule Your Insulation Removal & Replacement Service in Georgetown Today

Call (254) 970-2136 now - a live person answers 24/7. We’ll schedule your free assessment, deliver a written price within 24 hours, and start only when you’ve approved the scope. Every job includes air sealing first, documented photos, and before-and-after blower-door numbers you can actually read. Under The Haven Standard since 2016: flat price, written warranty, proven results.

Written by Wes Okafor, Owner at Topside Attic Insulation Georgetown, serving Georgetown, Round Rock, Brushy Creek, and Central Texas since 2016.