Insulation in Hornsby Bend, TX
Crawl space encapsulation and vapor barrier installation in Hornsby Bend typically runs $3,200-$6,800 for the full perimeter-and-floor treatment most homes here need, with attic radiant barrier and air sealing adding $1,800-$4,200 depending on square footage and existing conditions. Every job starts with a written price and ends with a documented photo record; on applicable work, you’ll get before-and-after blower-door numbers showing exactly how much air your building envelope was losing. Call (254) 970-2136 for a free estimate.
Why Hornsby Bend Homes Are Different
Hornsby Bend sits in the Colorado River bottomland floodplain east of Austin, where persistently elevated soil moisture and proximity to the river create crawlspace and under-floor humidity conditions meaningfully worse than higher-elevation suburbs just a few miles away. The clay soils here hold moisture year-round against unencapsulated crawlspaces, so insulation work demands vapor barrier integrity and moisture-resistant materials as a baseline. Skip those steps and you’ll see rapid R-value loss and mold growth in ways that simply aren’t as common in drier, upland communities like Pflugerville or Manor.
The housing stock is a patchwork of older rural ranch homes, manufactured housing, and agricultural outbuildings - many built well before modern energy codes and with minimal or long-degraded insulation. Eastern Travis County’s development pressure is now layering in newer spec construction, creating a split market between full retrofits of under-insulated legacy structures and code-compliance installs on new builds. The February 2021 Winter Storm Uri also exposed severe freeze vulnerability in the area’s older, poorly insulated rural homes, driving demand for winterization retrofits that had rarely been requested before.
Our Main Hornsby Bend Services
Hornsby Bend homeowners call us most often for attic work and spray foam; here’s what those jobs look like locally.
Attic Insulation in Hornsby Bend
Attic insulation in Hornsby Bend has to account for the Colorado River corridor’s amplified summer heat load - Austin regularly logs 60+ days above 95°F, and the bottomland humidity adds latent heat that makes attic performance critical. We find many older ranch homes here with original fiberglass batts compressed well below their labeled R-value, or with gaps where additions were cobbled together. We start every attic job with a blower-door test to measure air leakage, seal what we find, then install to the written scope. Attic Insulation in Hornsby Bend includes documented before-and-after photos and blower-door readings.
Spray Foam Insulation in Hornsby Bend
Spray foam insulation in Hornsby Bend works particularly well for the area’s mixed housing stock - it air-seals and insulates in one pass, which matters when you’re dealing with irregular framing in older rural homes or the tight envelope requirements of newer spec builds. We use open-cell and closed-cell formulations from Icynene and Demilec, selected by application, never pushed as a default. The material cost runs higher than batt or blown-in, but the air-sealing value often eliminates a separate step. Spray Foam Insulation in Hornsby Bend jobs get the same written price and photo documentation as every other service.
Blown-In Insulation in Hornsby Bend
Blown-in insulation in Hornsby Bend is our most common retrofit for attics with existing but inadequate coverage - we blow GreenFiber cellulose or Owens Corning fiberglass over sealed top plates and penetrations to achieve consistent depth without the labor of hand-placing batts. It’s especially cost-effective for manufactured homes in the area, where attic access is limited and weight matters. We mark target depth lines on joists and photograph coverage before we leave. Blown-In Insulation in Hornsby Bend includes the Haven Standard written scope and warranty.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterCrawl Space Encapsulation & Vapor Barrier in Hornsby Bend
Contractors working Hornsby Bend routinely pull out fiberglass batt insulation from crawlspaces and floor assemblies that is visibly saturated or mold-blackened - a direct result of the bottomland clay soils holding moisture year-round against unencapsulated crawlspaces. Full crawlspace encapsulation almost always has to precede any insulation upgrade here, adding a step that surprises homeowners used to quotes from elsewhere in the Austin metro. Crawl Space Encapsulation & Vapor Barrier is the foundation of our work in this market; we won’t install floor insulation over a damp, unsealed crawlspace.
Crawl Space Vapor Barrier
Signs you need it
Your crawlspace dirt floor shows standing water after rain, or fiberglass batts hanging between joists are blackened, compressed, or dropping out.
What it costs in Hornsby Bend
A 6-mil to 20-mil vapor barrier installed over the dirt floor in a typical Hornsby Bend crawlspace runs $1,200-$2,800, with thicker mil ratings and full wall extension toward the higher end.
How we do it
We remove debris and old fallen insulation, grade the dirt floor, lay overlapping seams of reinforced polyethylene, seal penetrations and piers with tape and mastic, and extend the barrier up foundation walls to the sill plate.
Crawl Space Encapsulation
Signs you need it
You smell mustiness inside the home, your floors feel cold and damp in winter, or you’ve had mold remediation that returned within two years.
What it costs in Hornsby Bend
Full encapsulation with sealed vapor barrier, wall insulation, dehumidifier, and conditioned-air supply in a Hornsby Bend crawlspace typically ranges $4,500-$9,500 depending on perimeter linear footage and existing water management needs.
How we do it
We install the vapor barrier floor and wall system, seal all vents and exterior access points, add rigid foam or closed-cell spray foam to walls, install a dedicated dehumidifier with condensate pump, and bring in a small conditioned-air supply to maintain positive pressure.
What Crawl Space Encapsulation & Vapor Barrier Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Vapor barrier (dirt floor only) | $1,200 - $2,800 |
| Partial encapsulation (walls + floor, no conditioning) | $3,200 - $5,800 |
| Full encapsulation with dehumidifier and air supply | $4,500 - $9,500 |
Can I just add insulation without encapsulating first?
No - we won’t do it, and any contractor who will is setting you up for mold and R-value loss within two seasons in Hornsby Bend’s moisture profile. The insulation will absorb ground moisture, compress, and potentially harbor mold that affects indoor air quality. Call (254) 970-2136 and we’ll walk through what your crawlspace actually needs.
How long does full encapsulation take?
Most Hornsby Bend crawlspace encapsulations take 2-4 days depending on access, existing debris, and whether we need to address standing water or drainage first. We provide a written schedule with the price before work starts. Call (254) 970-2136 for a free estimate.
Radiant Barrier Installation in Hornsby Bend
The Colorado River corridor amplifies Central Texas’s already brutal summers, with localized bottomland humidity adding latent heat load that makes attic radiant barriers more critical here than on the drier plateau to the west. Many Hornsby Bend homes - especially older ranch houses with dark shingle roofs and minimal attic ventilation - see attic temperatures exceed 140°F in July, forcing HVAC systems to run continuously and shortening equipment life. Radiant Barrier Installation blocks radiant heat transfer from roof deck to attic floor, reducing that load measurably.
Attic Radiant Barrier
Signs you need it
Your attic feels like a furnace by 10 a.m., your AC runs nonstop after noon, or your second-story rooms stay uncomfortably hot despite adequate insulation depth.
What it costs in Hornsby Bend
Radiant barrier installed across attic joists or stapled to roof deck rafters in a typical Hornsby Bend home runs $1,400-$3,200 for coverage up to 2,500 square feet of attic floor.
How we do it
We select perforated foil or woven fabric barrier depending on your attic ventilation strategy, install with proper air gaps, avoid compressing existing insulation, and photograph coverage and fastening before we leave.
Radiant Barrier Roof Deck
Signs you need it
You’re re-roofing or have limited attic floor access due to ductwork or storage platforms, but still need radiant heat reduction.
What it costs in Hornsby Bend
Roof-deck application during re-roofing or as a standalone retrofit in Hornsby Bend typically runs $2,000-$4,500 depending on roof pitch, accessibility, and whether we’re working around existing decking.
How we do it
We staple double-sided radiant barrier foil directly to underside of roof decking or to rafters with required 3/4-inch minimum air gap, seal edges and penetrations, and verify no obstruction of soffit-to-ridge ventilation paths.
What Radiant Barrier Installation Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Attic floor radiant barrier (foil over joists) | $1,400 - $3,200 |
| Roof deck radiant barrier (rafter/deck application) | $2,000 - $4,500 |
| Radiant barrier with attic air sealing package | $2,800 - $5,800 |
Does radiant barrier work with my existing insulation?
Yes - radiant barrier complements rather than replaces insulation, reflecting radiant heat so your existing fiberglass or cellulose doesn’t have to absorb and slow it. In Hornsby Bend’s climate, the combination typically reduces attic heat gain 20-35 percent. Call (254) 970-2136 for a free estimate.
Can you install radiant barrier in a finished attic?
Finished attics with limited access usually need roof-deck application or a retrofit during re-roofing; we assess access and ventilation during our initial inspection and quote only what will actually perform. Call (254) 970-2136 to schedule.
Insulation Removal & Replacement in Hornsby Bend
Hornsby Bend’s patchwork of older rural ranch homes, manufactured housing, and agricultural outbuildings means we regularly remove insulation that was inadequate from installation or has degraded past function - often decades-old fiberglass batt compressed to half its labeled R-value, or material contaminated by roof leaks, rodent activity, or the area’s persistent crawlspace moisture. Insulation Removal & Replacement starts with assessment: we photograph what we find, test for asbestos in pre-1990 material, and provide a written scope before any removal begins.
Contaminated Insulation Removal
Signs you need it
You see visible mold, rodent droppings, or saturated compressed batts in your attic or crawlspace, or you smell mustiness that worsens when the HVAC runs.
What it costs in Hornsby Bend
Contaminated insulation removal with HEPA containment, bagging, and proper disposal in Hornsby Bend runs $1,800-$4,200 for a typical attic, with crawlspace removal toward the higher end due to restricted access.
How we do it
We establish negative air pressure with HEPA filtration, remove material in sealed bags, treat exposed framing with antimicrobial where indicated, and provide photo documentation of the cleared space before any new insulation is specified.
Insulation Replacement
Signs you need it
Your insulation is below current code depth, has settled or compressed, or was removed due to contamination and the space is now bare.
What it costs in Hornsby Bend
Replacement with new blown-in fiberglass or cellulose to modern depth in a Hornsby Bend attic typically runs $2,200-$5,400, with spray foam replacement in walls or rim joists running higher depending on access.
How we do it
We air seal first - top plates, penetrations, can lights, duct boots - then install to the specified depth with marked joist lines, photograph coverage, and provide the written warranty and blower-door numbers on applicable jobs.
What Insulation Removal & Replacement Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Contaminated attic insulation removal | $1,800 - $4,200 |
| Standard insulation replacement (blown-in attic) | $2,200 - $5,400 |
| Full removal + replacement with air sealing | $4,500 - $9,800 |
Do I have to leave during insulation removal?
For standard fiberglass or cellulose removal, no - we contain the work area and run HEPA negative air machines. For confirmed hazardous material or extensive rodent contamination, we may recommend temporary relocation and will specify this in the written scope. Call (254) 970-2136 to discuss your situation.
How do I know if my old insulation has asbestos?
Pre-1990 vermiculite or early fiberglass batts may contain asbestos; we test before disturbing any material we suspect, and we never guess. If positive, we refer to licensed abatement and resume our work after clearance. Call (254) 970-2136 for an inspection.
Attic Air Sealing in Hornsby Bend
Attic air sealing in Hornsby Bend is where we start every job that involves the building envelope - it’s the hard prerequisite, not an upsell, and it’s especially critical in the area’s older ranch homes where top plates were never sealed and can lights were cut into ceilings without regard for thermal boundary integrity. The February 2021 freeze proved how much conditioned air these homes lose: we measured pre-sealing blower-door readings above 4,000 CFM50 in multiple Hornsby Bend homes, then cut that by 40-60 percent with targeted air sealing before adding any insulation. Attic Air Sealing is Haven Standard Clause 1 work - written price, written scope, written warranty.
Top Plate & Penetration Sealing
Signs you need it
Your attic floor has visible gaps where wall top plates meet drywall, or you feel drafts at outlets and switches on exterior walls during winter.
What it costs in Hornsby Bend
Top plate and penetration sealing with caulk, foam, and fire-rated sealant in a typical Hornsby Bend attic runs $1,200-$2,800, with complex multi-level attics toward the higher end.
How we do it
We identify all top plate gaps, plumbing and electrical penetrations, and chase openings, seal with appropriate material for each penetration type, and verify with blower-door test before and after to document the reduction in CFM50.
Can Light & Duct Boot Sealing
Signs you need it
You see dusty streaks around ceiling can lights, or your HVAC ducts blow conditioned air into the attic instead of the rooms below.
What it costs in Hornsby Bend
Can light sealing with fire-rated covers and duct boot sealing with mastic and mechanical fasteners in Hornsby Bend typically runs $800-$2,200 depending on fixture count and duct configuration.
How we do it
We install pre-formed fire-rated enclosures over IC and non-IC can lights, seal duct boots to drywall with mastic and strapping, and pressure-test the duct system where accessible to confirm no residual leakage.
What Attic Air Sealing Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Top plate and penetration sealing | $1,200 - $2,800 |
| Can light and duct boot sealing | $800 - $2,200 |
| Full attic air sealing (comprehensive package) | $2,200 - $5,200 |
Will air sealing make my attic too humid?
No - by sealing the attic floor, we’re stopping moisture-laden interior air from escaping into the cold attic space where it condenses. Proper attic ventilation (soffit and ridge) handles any residual moisture. In Hornsby Bend’s humid climate, this actually reduces condensation risk. Call (254) 970-2136 for a free estimate.
How much does air sealing lower my energy bills?
Most Hornsby Bend homes we seal show 15-30 percent reduction in heating and cooling load, with older, leakier homes at the higher end. The blower-door number tells the story: we show you the before-and-after CFM50 so you can verify the improvement yourself. Call (254) 970-2136 to schedule.
Wall Insulation in Hornsby Bend
Wall insulation in Hornsby Bend addresses a gap that many homeowners don’t discover until they live through their first summer or winter: the area’s older ranch homes and manufactured housing often have empty wall cavities, or fiberglass batts that settled and left cold zones, while newer spec builds may meet code but still underperform on thermal bridging. We insulate walls from the interior with minimal disruption or, where siding is being replaced, from the exterior for full cavity fill. Wall Insulation in Hornsby Bend requires matching the method to the wall construction - we don’t default to one approach.
Injection Foam Wall Insulation
Signs you need it
Your walls feel cold to the touch in winter, your home has no insulation or settled batts in exterior walls, or you’re finishing a room addition and want full cavity fill without removing drywall.
What it costs in Hornsby Bend
Injection foam wall insulation for a typical 1,500-square-foot Hornsby Bend home with 2×4 construction runs $3,500-$7,200, with 2×6 walls or multi-story homes toward the higher end.
How we do it
We drill 5/8-inch holes through exterior siding or interior drywall at stud-bay intervals, inject slow-rise foam to fill the cavity without bowing studs, plug and finish the holes, and verify fill completeness with thermal imaging.
Drill & Fill Wall Insulation
Signs you need it
You have empty wall cavities in an older Hornsby Bend home built before insulation was standard, or you’re replacing siding and want to insulate before the new exterior goes on.
What it costs in Hornsby Bend
Drill and fill with dense-pack cellulose or fiberglass in a typical Hornsby Bend ranch home runs $2,800-$5,800, with exterior access during re-siding reducing labor cost.
How we do it
We remove a row of siding or drill through exterior sheathing, blow cellulose or fiberglass to specified density with continuous hose movement to avoid voids, verify density with wall-cavity pressure readings, and seal all penetrations.
What Wall Insulation Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Injection foam (2×4 walls, interior access) | $3,500 - $7,200 |
| Drill and fill dense-pack (exterior access) | $2,800 - $5,800 |
| Exterior wall insulation during re-siding | $4,200 - $8,500 |
Will injection foam damage my walls?
Slow-rise formulations and controlled injection pressure prevent stud bowing and drywall distortion; we’ve completed hundreds of injections without structural damage. We photograph the process and show you the thermal imaging verification. Call (254) 970-2136 for a free estimate.
Can you insulate walls without removing drywall?
Yes - injection foam and dense-pack cellulose both fill cavities through small holes that we patch and paint to match. The alternative is insulating from the exterior during re-siding, which we also do. Call (254) 970-2136 and we’ll recommend the right method for your home.
Attic Cleaning & Rodent Proofing in Hornsby Bend
Attic cleaning and rodent proofing in Hornsby Bend is often the first step before any insulation work can proceed - the area’s rural-to-suburban transition means mature trees, agricultural surroundings, and older structures with multiple entry points create conditions where squirrels, rats, and mice establish attic colonies year-round. We find shredded insulation used as nesting material, contaminated vapor barriers, and chewed wiring that poses fire risk. Attic Cleaning & Rodent Proofing includes full decontamination, entry-point sealing, and documentation of what we found and what we fixed.
Attic Sanitizing & Decontamination
Signs you need it
You hear scratching in ceilings, find droppings or urine stains on insulation, or smell ammonia-like odor that intensifies in summer heat.
What it costs in Hornsby Bend
Attic sanitizing and decontamination with HEPA vacuuming, enzyme treatment, and antimicrobial application in a typical Hornsby Bend attic runs $1,400-$3,600, with heavy contamination or large attic square footage toward the higher end.
How we do it
We remove contaminated insulation and debris, HEPA-vacuum all surfaces, apply enzyme digester to break down organic waste, follow with antimicrobial where indicated, and provide photo documentation of the sanitized space before any new insulation is installed.
Rodent Proofing & Exclusion
Signs you need it
You’ve had recurring rodent activity despite trapping, or you can see gaps around roof penetrations, soffit vents, or foundation lines where animals enter.
What it costs in Hornsby Bend
Rodent proofing and exclusion with hardware cloth, metal flashing, sealant, and one-way exit devices for a typical Hornsby Bend home runs $1,200-$3,200, with multiple entry levels or complex rooflines toward the higher end.
How we do it
We inspect roofline, soffits, vents, chimney gaps, and foundation with photo documentation, install rodent-resistant materials at all entry points, place one-way exits where active colonies exist, and return to verify no re-entry before sealing final exits.
What Attic Cleaning & Rodent Proofing Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Attic sanitizing and decontamination | $1,400 - $3,600 |
| Rodent proofing and exclusion | $1,200 - $3,200 |
| Full attic restoration (cleanout + proofing + re-insulation) | $4,500 - $10,500 |
Do you handle the rodents or just seal after?
We provide complete exclusion including one-way exits for active colonies; we don’t set poison bait that leaves dead animals in walls. For severe infestations, we coordinate with wildlife control specialists and resume our work after clearance. Call (254) 970-2136 to discuss your situation.
How do I know if rodents have damaged my insulation?
Shredded or displaced batts, tunnels through blown-in material, and dark staining from urine are visible signs we document during inspection. Even without visible damage, rodent activity compromises R-value and indoor air quality. Call (254) 970-2136 for a free inspection.
Home Energy Audit in Hornsby Bend
A home energy audit in Hornsby Bend gives you the diagnostic foundation for every other decision about your building envelope - especially critical in this market where the split between legacy rural homes and newer spec construction means there’s no standard approach that applies across properties. We use blower-door testing, thermal imaging, and duct leakage measurement to show exactly where your conditioned air escapes and where insulation is missing or compromised. Home Energy Audit includes a written report with prioritized recommendations and estimated savings; many Hornsby Bend homeowners use this to phase work over multiple seasons.
Blower Door Test
Signs you need it
Your energy bills are higher than comparable homes, you feel drafts despite closed windows, or you’re planning insulation work and want baseline performance data.
What it costs in Hornsby Bend
A standalone blower-door test with written report in Hornsby Bend runs $350-$650, with the cost credited toward any envelope work we complete within 90 days.
How we do it
We install a calibrated fan in an exterior door, depressurize the house to -50 Pascals, measure CFM50 leakage rate, and use smoke pencils and thermal imaging to locate dominant leakage paths while the house is under test pressure.
Thermal Imaging Inspection
Signs you need it
You have uneven temperatures between rooms, suspect missing insulation in walls or ceilings, or need documentation of conditions for an insurance or real estate transaction.
What it costs in Hornsby Bend
Thermal imaging inspection as part of a full energy audit or as a standalone service in Hornsby Bend runs $250-$550, with full audit packages including blower-door and duct testing at combined rates.
How we do it
We scan interior and exterior surfaces with a calibrated FLIR camera during conditions that maximize temperature differential, interpret images for insulation gaps, moisture intrusion, and air leakage patterns, and include annotated thermal photos in your written report.
What Home Energy Audit Costs in Hornsby Bend
| Item | Typical range in Hornsby Bend |
|---|---|
| Blower-door test with written report | $350 - $650 |
| Thermal imaging inspection (standalone) | $250 - $550 |
| Full home energy audit (all diagnostics) | $600 - $1,200 |
Is an energy audit worth it if I’m not ready to do the work?
Yes - the written report lets you phase improvements by cost and impact, and many Hornsby Bend homeowners use our priority list to tackle air sealing first, then insulation, then HVAC rightsizing as budget allows. The blower-door number alone changes how you understand your home. Call (254) 970-2136 to schedule.
How long does a full energy audit take?
Plan on 3-4 hours for a complete audit including blower-door test, thermal imaging, and duct leakage testing; we need the house unoccupied or with occupants in a single room for accurate depressurization. You receive the written report within 48 hours. Call (254) 970-2136 to book.
Brands We Service in Hornsby Bend
We source materials from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber - no proprietary lock-in means we specify what’s right for your assembly, not what’s in our warehouse. Common stock items for Hornsby Bend jobs ship within 24-48 hours from regional distributors. See our brands for full specifications.
Pricing for Insulation in Hornsby Bend, TX
| Service | Typical range in Hornsby Bend |
|---|---|
| Crawl space vapor barrier | $1,200 - $2,800 |
| Full crawl space encapsulation | $4,500 - $9,500 |
| Attic radiant barrier | $1,400 - $3,200 |
| Roof deck radiant barrier | $2,000 - $4,500 |
| Contaminated insulation removal | $1,800 - $4,200 |
| Insulation replacement (blown-in attic) | $2,200 - $5,400 |
| Attic air sealing (full package) | $2,200 - $5,200 |
| Injection foam wall insulation | $3,500 - $7,200 |
| Attic sanitizing and decontamination | $1,400 - $3,600 |
| Rodent proofing and exclusion | $1,200 - $3,200 |
| Full home energy audit | $600 - $1,200 |
Prices in Hornsby Bend push toward the higher end when we encounter standing water in crawlspaces, asbestos-containing material requiring abatement referral, or complex rooflines that slow radiant barrier installation. Every job still begins with a written price under Haven Standard Clause 1 - no work starts without it.
Neighborhoods We Serve in Hornsby Bend
Our crews cover the full Hornsby Bend area with same-day response typically available for urgent moisture or rodent issues. We regularly work in:
- Hornsby Bend proper and riverfront properties
- Blue Bluff Road corridor
- Webberville Road area
- FM 969 corridor east of Austin
- Colorado River bottomland developments
Dispatch and scheduling are coordinated from our Austin office; crews serve Hornsby Bend locally with no callback windows measured in business days.
Service Area - Cities Near Hornsby Bend
We serve the full Travis and Williamson County corridor, with regular work in Georgetown, TX, Round Rock, TX, Brushy Creek, TX, and Leander, TX. Each market gets the same Haven Standard: written price before work, documented photo record after, and before-and-after blower-door numbers on applicable jobs.
Serving Hornsby Bend, TX - Our Local Coverage Area
We’re based in the Hornsby Bend area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Hornsby Bend
Most attic and wall insulation retrofits in unincorporated Travis County don’t require permits, but crawlspace encapsulation with structural modifications or new electrical for dehumidifiers may trigger review. We verify permit requirements during our initial inspection and include any fees in your written price. Call (254) 970-2136 to confirm for your specific project.
We answer calls 24/7 with a live person, and same-day response is typically available for active water intrusion or mold concerns in Hornsby Bend. We don’t use voicemail loops or business-day callback windows. Call (254) 970-2136 now if you’re seeing standing water or smelling mustiness.
Yes - we serve the full eastern Travis County area including outlying ranch properties and agricultural buildings. Travel is included in your written price; we don’t add surprise mileage fees after quoting. Call (254) 970-2136 with your location and we’ll confirm scheduling.
Ready to fix your building envelope? Call (254) 970-2136 for a free estimate. We’ll provide a written price before any work starts, a documented photo record when we’re done, and before-and-after blower-door numbers on every applicable job. That’s the Haven Standard, and it’s how we’ve operated since 2016.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 1-hour.
- 4You approve before work beginsNothing starts until you say go.
What Hornsby Bend Customers Say
"Fixed price, clean work, and they hauled the old material away as agreed."
- Todd M."They air-sealed the attic floor before insulating and showed me the blower-door number before and after. The upstairs is finally the same temperature as downstairs."
- Marisol D."They photographed rodent damage in the old insulation that we had no idea about, and priced the exclusion work separately so we could decide."
- Harriet N.